Atmos 528, 526, 519 Tools

Jaeger%20LeCoultre%20Atmos

Repair tools for the Jaeger LeCoultre Atmos clocks model #2, 519, 526, 528.

Sort By:  
Crown nut lock wrench
Use to lock the castle nut while adjusting the regulator
$7.95
Rubber feet for Atmos clock
Replacement rubber feet for your Jaeger LeCoultre Atmos clock
$6.95
Senson Flag
If you use a Microset then this product is for you.
$5.00
1/4 Buff Stick
This buff stick is excellent for polishing the roller on both all models of Atmos clocks
$9.95
Chain for Jaeger LeCoultre Atmos clock
Aftermarket Atmos replacement chain. Pulley Not Included
$9.95
Atmos bubble level repair kit
Repair those dead bubble levels
$19.95
Atmos balance tube clamp
Clamp to hold the balance tube to unscrew pendulum and suspension spring.
$19.95
Atmos suspension wire puller
$9.95
Jaeger LeCoultre Style Torque Tool
This tool is used to measure the power of the mainspring on the Atmos models #2, 519, 526, 528
$85.00
Atmos chain puller
Makes the job of catching and pulling the atmos chain easy
$9.95
528 repair notes
If you are planning on repairing the Atmos model 526 or 528 these repair notes are a must
$9.95
Crown nut lock wrench
519-526-528 Atmos Castel Nut Lock Wrench (519Reg)
This mini regulator adjuster to works great for adjusting the regulator back to center. This small tool is easy to use, instead of adjusting the regulator from the front and trying to work around the tool this tool works from the back and allows easy access to the regulator. Made of high impact PETG this tool will last for years.
Use to lock the castle nut while adjusting the regulator
$7.95
Rubber feet for Atmos clock
New Rubber Feet For Model 2, 519, 526 and 528 (RF)
If your clock is missing one or more of those rubber feet used on the Atmos mode#2, 519, 526 or 528 than these are just what you are looking for. Don't mar up the nice furniture replace those missing feet with these. They come in a set of three and all you need to do is add a small amount of glue to the bottom of the new foot and press it into place.
Replacement rubber feet for your Jaeger LeCoultre Atmos clock
$6.95
Senson Flag
Sensor Flag (SFMD)
This sensor flag was designed to be easily installed and removed from the Atmos pendulum so you can time out your Atmos clock. This small nylon flag slips onto the bottom of the pendulum and will trip the Microset optical detector. These flags comes 6 to a pack and are attached to their base until needed.
If you use a Microset then this product is for you.
$5.00
1/4 Buff Stick
1/4" wide Leather Buff Stick (BSJLH)
This leather buff stick is excellent for polishing the roller on all models of the Jaeger LeCoultre Atmos clock. The buff stick is 8" ;png and 1/4' wide has a leather face, just add rouge and it is ready to go. The rubber coated handles gives you a sure grip during polishing.
This buff stick is excellent for polishing the roller on both all models of Atmos clocks
$9.95
Chain for Jaeger LeCoultre Atmos clock
Atmos Chain (atmos chain)
Here is a aftermarket replacement chain for all models of the Jaeger LeCoultre Atmos clock. The chain is 3" long and gold tone in color. Pulley Not Included
Aftermarket Atmos replacement chain. Pulley Not Included
$9.95
Atmos bubble level repair kit
Atmos Bubble Level Repair Kit (BBkit)
This kit includes a new bubble level, cement and instruction for repairing the bubble level in the 540, 560 and later model 528. If your clock has 3 screws that hold your bubble in then this kit will work on it.
Repair those dead bubble levels
$19.95
Atmos balance tube clamp
Atmos Balance Wheel Tube Clamp (StClmp)
Sometimes no matter how hard you try you just can't break that nut loose on the bottom of the Atmos balance. This small clamp will fit around the tube and allow you to clamp it in the vice and break that nut free. It is also good to help unscrew the Atmos suspension spring lower block. Vice and balance tube not included.
Clamp to hold the balance tube to unscrew pendulum and suspension spring.
$19.95
Atmos Suspension Wire Puller (SP01)
Make that job of rethreading a new suspension spring through the balance tube as easy as 1-2-3 . Just insert the Atmos suspension spring puller through the balance tube, fit the tip of the suspension wire in the end, lock in place and pull in through. Work smart not hard. Balance stem not included.
Atmos suspension wire puller
$9.95
Jaeger LeCoultre Style Torque Tool
Jaeger LeCoultre Model 2 - 528 Torque Tool (519TT)
If you repair the Jaeger LeCoutre Atmos clock model #2, 519, 526 or 528 than this tool is a must have. This tool was made to measure the torque of the mainspring so that it can be wound up to the required specification. If the clock is not wound to the proper specification it could either stop, run erratic or rebound from being overwound. Stop the troublesome returns by making sure the clock is wound to the proper specs before it leaves the shop. This tool can also be used when a clock comes into the shop to test the torque on the mainspring to verify the bellow is working correctly and keeping the clock wound correctly. Included in the sale is a FREE copy of the Jaeger LeCoultre 528 Repair Notes. The torque tool comes with a 1 year limited warranty.
This tool is used to measure the power of the mainspring on the Atmos models #2, 519, 526, 528
$85.00
Atmos chain puller
Atmos Chain Puller (ChPl)
The Atmos chain puller is made out of super strong music wire that will last for years. Just feed the hook through the 52mm spring guide and hook it onto the chain, pull it back through and pin it.
Makes the job of catching and pulling the atmos chain easy
$9.95
528 repair notes
Atmos 528 Repair Notes (528notes)
This 10 page booklet is a must have for anybody planning on working on the Jaeger LeCoultre 526 or 528. The booklet give you the specifications for repairing these clock as well as some detailed pictures. The last 4 pages are pictures and part numbers for the model 526 and 528.
If you are planning on repairing the Atmos model 526 or 528 these repair notes are a must
$9.95
Per Page      1 - 11 of 11
  • 1